PyGo2 includes charging cradle


Cellular LTE-M (Cat NB1 and M1) multipurpose wearable device featuring Pymesh and the following…

  • LTE-M (Cat NB1 and M1), LoRa, WiFi and Bluetooth
  • OLED
  • GPS
  • Accelerometer
  • State of the art antennas
  • LiPo battery
  • 6 exposed pins (2 charging/4 universal in/out)

In stock




Meet the PyGo2 which is in essence a FiPy module on steroids! We packed the FiPy in an IP6X case, gave it an OLED, a GPS, an accelerometer, some state of the art antennas, and a LiPo battery. The PyGo2 features six exposed pins: 2 for power and 4 universal inputs/outputs with digital/analogue capabilities so that you can connect different types of sensors and actuators. Developers can physically connect Things and sensors to a PyGo!

Best of all, the PyGo modules are used with the Pylife Mobile App for Android and iOS and can link up with other Pycom modules. We launched the PyGo modules with the ability to mesh together at distance of up to 12KM. PyGo2 includes WiFi, Bluetooth, LoRa and dual LTE-M (embedded SIM for CAT M1 and NB-IoT from 1NCE) the PyGo2 gives access to all the world’s LPWAN networks on one tiny board.

If you are purchasing the PyGo2 and wish to connect via USB to your computer, you will also need to purchase either the PyGo cradle.


PyGo2 Features

  • Powerful CPU
  • Pylife Mobile App for Android and iOS
  • Five networks: WiFi, BLE, cellular LTE-CAT M1/NB1 (embedded SIM chip), LoRa and LoRa MESH
  • Up to 1KM WiFi range
  • Ultra-low power usage: a fraction compared to other connected microcontrollers
  • Pymakr IDE supported
  • OLED
  • IP6X rated



  • Espressif ESP32 SoC
  • Dual processor and WiFi radio system on chip
  • Networking processor handles the WiFi connectivity and the IPv6 stack
  • Main processor is entirely free to run the user application
  • An extra ULP-coprocessor that can monitor GPIOs, the ADC channels and control most of the internal peripherals during deep-sleep mode while only consuming 25uA



  • Analog channels: 8_12 bit ADCs, 2_8 bit DAC
  • Timers: 2_64 bit with PWM with up to 16 channels
  • DMA on all peripherals
  • 2 Pins (Power)
  • GPIO: 4 analog input (0-3.3V 12bit SAR ADC) and digital (3.3V logic) input/output pins.


Hash / Encryption

  • SHA, MD5, DES, AES


WiFi Networking

  • 802.11b/b/n 16mbps



  • Low energy and classic



  • Running at 32KHz



  • Node range: Up to 50km


Security & Certifications

  • SSL/TLS support up to 1.2
  • WPA Enterprise security
  • AES encryption engine



  • RAM: 4MB
  • Flash Memory: 8MB
  • Hardware floating point acceleration
  • Python multi-threading



  • LiPo battery: 420mAh LiPo 4.2V



  • Connect up to 200 devices in a mesh using our LoRa mesh technology


Sigfox Operating Frequencies

  • RCZ1 – 868MHz(Europe)
  • RCZ2 – 902MHz (US, Canada and Mexico)
  • RCZ3 – (Japan and Korea)
  • RCZ4 – 920-922MHz (ANZ, Latin America and S-E Asia)


Sigfox Specification

(Hardware capable but no longer supported)

    • Semtech SX1272 – Long Range, Low Power RF Transceiver 860-1000MHz with LoRa® Technology
    • Class 0 device. Maximum Tx power:
    • – 14dBm (Europe)
    • – 22dBm (America)
    • – 22dBm (Australia and New Zealand)
      • Node range: Up to 50km
      • Sigfox pre-certified (October 2016)
      • Power
  • Sigfox (Europe): 17mA in Rx mode, 47mA in Tx mode and 0.5uA in standby
  • Sigfox (Australia, New Zealand and South America):
  • 24mA in rX mode, 257 mA in Tx mode and 0.5uA in standby


Bluetooth Networking

  • Low energy and classic
  • Compliant with Bluetooth v4.2 BR/EDR and BLE specification
  • Class-1, Class-2 and Class-3 transmitter without external power amplifier
  • Enhanced power control
  • 10dBm transmitting power
  • NZIF receiver with -98 dBm sensitivity
  • Adaptive Frequency Hopping (AFH)
  • Standard HCI based on SDIO/SPI/UART
  • High speed UART HCI, up to 4 Mbps
  • BT 4.2 controller and host stack
  • Service Discover Protocol (SDP)
  • General Access Profile (GAP)
  • Security Manage Protocol (SMP)
  • Bluetooth Low Energy (BLE)
  • HID
  • All GATT-based profile supported
  • SPP-Like GATT-based profile
  • BLE Beacon
  • CVSD and SBC for audio codec
  • Bluetooth Piconet and Scatternet


LoRa Operating Frequencies

  • 868MHz(Europe) at 14dBm maximum
  • 915MHz (North and South America, Australia and New Zealand) at 20dBm maximum


LoRa Specification

  • Power consumption: 10mA Rx, 28mA Tx
  • LoRaWAN stack – Class A and C devices
  • Node range: Up to 20km
  • Nano-gateway: Up to 12km (Capacity up to 200 nodes)


LTE-M Operating Frequencies

  • 34 bands supports from 699Mhz to 2170Mhz (Total world-wide support)


LTE-M Specification

    • One single chip for both CAT-M1 and -NB1 (yes, only one chip)
    • 3GPP release 13 LTE Advanced Pro
    • Supports narrowband LTE UE categories M1/NB1
    • Integrated baseband, RF, RAM memory and power management
    • Reduced Tx power class option
    • Peak power estimations: TX current = 420mA peak @1.5Watt RX current = 330mA peak @1.2Watt
    • – Data rates:

      • 300 kbps DL
      • 375 kbps UL (LTE Cat M1 in 1.4 Mhz, HD-FDD)
      • 40 kbps DL
      • 55 kbps UL (LTE Cat M2 in 200 kHz, HD-FDD)


Tx/Rx Frequencies

Ports for LTE Bands
Tx frequencies
Rx frequencies
Low bands 5, 8, 12, 13, 18, 19, 20, 28
699 to 915 MHz
729 to 960 MHz
Mid bands 1, 2, 3, 4
1710 to 1980MHz
1805 to 2170 MHz


WiFi Networking

      • Up to 1km range
      • 802.11b/g/n 16mbps
      • Power: 12mA in active mode, 5uA in standby



      • 41 x 20 x 22.5 (mm)



    • 26g
    • 50g (Packaged)

Additional information

Weight 0.026 kg
Dimensions 4.1 × 2.4 × 1.25 cm

26 g


41 x 24 x 12.5 (mm)

You may also like…